Page 1
06 41 00.11/COM
BuyLine 5802

Page 2
Pin Tumbler Door
& Drawer Locks
Schlage C
& CCL R-1 keyways
Schlage C keyway cabinet locks
available in cylinder sizes of 1 1/8”
& 1 3/8” in dead bolt type for door
and drawer applications. Cabinet locks
can be master keyed to door hardware,
providing the convenience of a single
key operation. Locks are available with
cylinder or less cylinder and will accept
Schlage originals and other manufacturers’
Schlage C compatible cylinders. Locks
are offered in 26D and 3 finish, six or five
pin tumbler. Spacers available for varying
material thickness. Master keying available.
CCL-R1 keyway pin tumbler door
and drawer locks, dead bolt type,
available in cylinder lengths of: 7/8”,
1 1/8”, 1 3/8.” Spacers are available
for varying material thickness. Cam
style locks also available in same
lengths as CompX National pin
tumbler door and drawer locks.
See below for part numbers.
Note: All CompX National, CCL
and Schlage keyway pin tumbler
locks are brass, not die-cast.
Deadbolt Locks.
Application. For drawers, right hand
and left hand doors. Surface mounted
and requires 57/64” diameter hole
for cylinder. Four or five pin tumbler
available in 26D, 4, & 4G finish.
Master keying by request.
ANSI/BHMA designation.
E07121 for cabinet door application
E07041 for cabinet drawer application
CompX National Drawer part numbers.
C8178 – material thickness to 7/8”
C8177 – material thickness to 1 1/8”
C8179 – material thickness to 1 3/8”
CompX National Doors part numbers.
C8173 – material thickness to 7/8”
C8174 – material thickness to 1 1/8”
C8175 – material thickness to 1 3/8”
Cam Locks.
Application. For drawer, right hand
or left hand. Surface mounted and
requires 57/64” diameter hole for
cylinder. Cam style with 90° turn.
Four or five pin available in 26D, 4,
& 4G finish. Master keying available.
ANSI/BHMA designation.
E07301 for drawer, E07321 for door.
CompX National part numbers.
C8183 – door, material thickness to 7/8”
C8188 – drawer, material thickness to 1 3/8”
Finish codes.
3 – Bright brass
4 – Satin brass
4G – Antique brass
26D – Dull chrome
The Advantage Plus
feature allows users
to remove the cylinder
while the lock remains
in place. NO mounting
screws need to be
removed. Simply use
a 5/64” Allen wrench
from the back to remove
the cylinder for re-keying.
Application. For drawer, right hand and
left hand doors. 90° cam turn, for overlay
application, the combined thickness
of front and frame cannot exceed the
cylinder length. Four or five pin available
in 26D, 4, & 4G finish. Master keying
available.
ANSI/BHMA designation. E07261
for cabinet drawer, RH and LH doors.
CompX National Drawer part numbers.
For flush Mount
C8102 – material thickness to 3/4”
C8106 – material thickness to 1 1/8”
C8108 – material thickness to 1 3/8”
For lipped / overlay mount
C8101– for material thickness to 5/8”
C8103 – for material thickness to 7/8”
C8109 – for material thickness to 1 1/2”
Application. Plunger style bolt action
for sliding wood doors and requires 7/8”
diameter mounting hole. Four
or five pin available in 26D, 4 finish.
Master keying available.
ANSI/BHMA designation. E07161.
CompX National part numbers.
C8142 – cylinder length 1 1/8”
C8143 – cylinder length 1 3/8”
ANSI/BHMA designation.
E07191, for sliding glass door
CompX National Part number.
C8140, in 26D finish only – ratchet type
grips inner bypassing sliding glass door,
lock case blocks outer door.
Pin Tumbler Cylinder Cam Locks,
Sliding Glass/Wood Door Locks
C8179
C8188
C8109
C8142
C8140
Schlage C Keyway

Page 3
Two styles with multiple deadbolt profiles
are available. These locks require a 16.5
mm diameter hole and can be mounted
either vertically or horizontally in 3⁄4”
material. They feature attractive
but tough nylon housing.
Our Double Door Type 250 Lock
can lock both doors without the use
of a spring catch.
Cam Locks
Most cam locks are available with either
90° or 180° rotation. They are available
in both vertical and horizontal mounts,
requiring a 16.5 mm diameter hole
and mounting in 3⁄4” thick material.
Cams change easily, with the use
of the TL-100, a tool available exclusively
from CompX Timberline.
Please note: CompX Timberline cam
locks must be installed so that they
lock in the counterclockwise position.
The Thick Panel Lock, Type 170,
comes packaged with two different cams
which can be assembled to the lock in three
orientations. This offers sufficient flexibility
to adapt to most locking situations.
The mounting flange adjusts to allow lock
to be mounted in panels from 7/8” thick
up to 1 3/8” thick. This lock also requires
a 16.5 mm diameter hole and allows
a 90° rotation only.
Gang Locks
Gang locks allow for the locking
of multiple drawers within one piece
of furniture. CompX Timberline offers
many variations of gang locks, mainly
differing in the position of the gang lock,
which can be mounted either
in the drawer front, fixed rail or on
the side. These systems install easily
and fit a wide variety of case designs.
CompX Timberline makes
glass door locks in two styles:
k Bore Through
k Compression Mount
Bore Through style locks are
made for swing style doors.
They mount in glass doors
up to 3/8” thick, either vertically
or horizontally. Cam must rotate
counterclockwise to lock. A cap
is attached to give a finished
appearance. Nut washer is hand-
tightened to fasten cylinder body
to glass. A 7/8” diameter hole
is bored in glass, centered
7/8” from edge.
Compression Mount style locks
are non-bore glass door locks. Fully
cushioned to avoid glass damage,
these locks mount in glass doors
1⁄4” to 5/16” thick, either vertically
or horizontally. The lock slips onto
the edge of glass doors at any
location, with no boring required.
All CompX Timberline glass door
locks are available in three lock plug
finishes: Bright Nickel, Bright Brass
and Satin Nickel.
Glass Door
Locks
Wardrobe Locks
Featuring a full 1⁄2” lockbar throw,
CompX Timberline’s wardrobe locks
only need machining for a 16.5 mm
lock hole. They can mount either
vertically or horizontally.
Available for desk files,
deep files and lateral files.
The attractive black finish
allows files to slide smoothly
and its durable design handles
heavy loads. Interlocking
components allow easy
installation and remove
the possibility of file rail
pull out.
File Frame
Deadbolt Locks
06 41 00.11/COM
BuyLine 5802
Types 250, 281
Types 170, 184
System 100
Type 355, Type 307
System 260
File Frame System

Page 4
CompX eLock
models
Numeric Keypad.
Provides authorization with a PIN code
of variable length.
EL-2004-KP
Magstripe Card.
Designed for secure confirmations
with existing mag stripe cards,
including credit cards.
EL-2004-MS
Magstripe / Keypad Dual System.
Mag card and numeric keypad
for dual control.
EL-2004-MSKP
Prox Reader.
Just wave the card and enter.
EL-2004-PR
Prox Reader / Keypad Dual System.
Prox reader and numeric keypad
for dual control.
EL-2004-PRKP
LockViewTM Software
k WindowsTM based
k Download, view, save, print, archive
and delete audit trails
k Add, edit, view and delete users
/ supervisors and their credentials
k Assign access rights between users
/ supervisors and CompX eLocks
in the database
k Time-based access restrictions
k Create user groups
k Dual credential access available
k Add, edit and delete CompX eLocks
k Set real time clock
k RJ11 / USB converter included
About eLocks
CompX eLock is a highly engineered
lock with a motor-driven latch. Its
uncompromising lock control electronics
include a non-volatile memory that stores
250 user / supervisor codes and audit trail.
Designated supervisor(s) can add
or delete users either at the eLock unit
or using optional LockViewTM software.
LockViewTM allows the operator
to download the last 1500 access attempts
and to maintain overall eLock management.
Totally Secure Operation.
When a valid credential is detected,
the green LED illuminates, the locking
mechanism opens and there is a positive
confirmation beep. If an invalid credential
is entered, the red LED illuminates,
and there is a negative beep.
Options.
k Power pack (120V or 230V)
k High decibel alarm box
k Dual latch control system
k Through door mounting available
k Electric strike
Keypad
k Numeric keypad with
variable length PIN code
(4 - 14 digits)
k Bevel is provided with
keys numbered 0-9,*, #
k Numbers are silk screened
on user-friendly buttons
k Keypad uses carbon
contacts to assure reliability
and increased durability
Magstripe
k Can program many
existing magstripe card
I.D.s currently in use
k Compatible with all
“Track 2” style cards
k The lock is capable
of accepting magnetic
stripe cards
k Simple operation with
the swipe of a card
For more information, please visit www.compxnet.com
PO Box 200
Mauldin, SC 29662
864.297.6655 phone
864.297.9987 fax
915 Sherwood Drive
Lake Bluff, IL 60044
847.234.1864, x16 phone
847.234.7922 fax
Western Distribution Center
9370 Buffalo Ave., Unit 104
Rancho Cucamonga, CA 91730
909.476.7933 phone
909.476.8553 fax
Prox
k Can program many existing proximity
card I.D.s currently in use
k Uses standard HID® proximity cards
k Non-contact proximity based system;
just wave the card in front of the lock
k Approximately 1 inch card read range
k Blank and custom-branded HID®
cards available
Applications
The eLock can be mounted:
k On cabinet doors
and drawers
k On medical carts,
patient files
k On hospital / pharmacy
refrigerators
Anywhere access control
is needed or required.
EL-2004-KP
EL-2004-MS
EL-2004-MSKP
EL-2004-PR
EL-2004-PRKP
Battery
Pack and Cable
Spring Bolt
CompX
eLock
(of your
choice)
eLock Kit
LockView is a trademark of CompX Security Products. HID is a trademark of HID Corporation. Windows is a trademark of the Microsoft Corporation.